Electrical Rough-In Services in Orlando, Florida
Electrical rough-in is the behind-the-walls wiring phase that happens after framing but before drywall installation. During this stage, our crew runs Romex cable (14/2 or 12/2 gauge), installs outlet boxes, switch boxes, and breaker panel connections, and routes conduit for future needs. In newer subdivisions like Hunters Creek, Doctor Phillips, and Azalea Park, homes often need upgraded rough-in to handle modern loads-kitchen circuits, dedicated appliance feeds, EV charging prep, and home office outlets. We size every circuit to code, label every wire, and ensure your home meets current electrical demands plus future expansion.
Our electrical rough-in process starts with a site walkthrough where we review your remodeling plans, load calculations, and code requirements specific to Orlando and surrounding areas like Winter Springs, Casselberry, and Maitland. Next, we map out all circuits, identify the breaker panel location, and install conduit runs and boxes according to NEC standards. Our electricians then run all branch circuits-individual runs to outlets, switches, and fixtures-and test continuity before the drywall crew arrives. Finally, we schedule the Orange County building inspection to certify the rough-in before final connections and trim-out. Most residential projects from Kitchen Remodeling to Bathroom Remodeling rough-in complete within 2-4 business days.
What Is Included
When you hire Renovating central Florida LLC for electrical rough-in, here is exactly what you get:
- 14/2 and 12/2 Romex cable installation for all branch circuits
- Outlet boxes, switch boxes, and fixture boxes installed per NEC spacing rules
- Dedicated circuits for kitchen appliances, bathrooms, and laundry per code
- Breaker panel upgrades or modifications if needed for load capacity
- Conduit runs for protection in high-traffic or exposed areas
- Continuity testing and wire labeling for easy identification during trim-out
- Orange County permit pull and building inspection coordination
Signs You Need Electrical Rough-In
- Flickering lights or dimming when running multiple appliances-sign of undersized circuits or poor connections
- Outlets that don't hold plugs firmly or feel warm to the touch-old rough-in or loose connections
- Tripped breakers during remodeling work-indication that existing circuits lack capacity
- No dedicated circuits for kitchen or bathroom-older homes in Conway, Belle Isle, and Edgewood often lack code-compliant setup
- Exposed or damaged wiring visible in walls or crawlspaces-safety hazard requiring immediate rough-in repair
- Planning a major remodel (kitchen, bathroom, or whole-home)-always upgrade rough-in to current code and add future circuits
- EV charging station or solar panel installation planned-rough-in must be sized for these high-amperage loads
- Adding home office, wet bar, or outdoor kitchen-new rough-in required to avoid overloading existing circuits
Our Electrical Rough-In Process
Design & Code Review
Our electrician meets with you and your general contractor to review the remodeling plans, count outlets and switches, calculate load requirements, and confirm compliance with 2020 NEC and Orange County Building Code. This step takes 1-2 hours and happens before any work begins.
Permit & Inspection Scheduling
We pull the electrical permit from Orange County (valid for 6 months) and coordinate the rough-in inspection timing. Permit pull typically takes 3-5 business days; inspection is usually scheduled 5-7 days after rough-in is complete.
Conduit & Box Installation
Our crew installs all outlet boxes, switch boxes, and fixture boxes according to NEC spacing requirements (typically 12 inches from studs for outlets, 48 inches max spacing). Conduit is run for areas requiring extra protection. This phase takes 4-8 hours depending on project size.
Wire Run & Circuit Installation
We run all branch circuits (14/2 for 15-amp, 12/2 for 20-amp, 10/2 for dedicated appliances) from the breaker panel to every box. Circuits are labeled at both ends for clarity. This typically requires 8-16 hours of labor.
Continuity Test & Final Check
Before drywall closes the walls, we test every circuit with a continuity tester, verify all connections are tight, and walk the home with you to confirm every outlet and switch location matches your plans. Final checks take 2-4 hours.
Building Inspection & Sign-Off
Orange County inspector verifies all rough-in work meets NEC code and local requirements. Inspection typically takes 30-60 minutes. Once approved, you receive the inspection sign-off card, and drywall installation can proceed.
Types of Electrical Rough-In We Handle
- Standard branch-circuit rough-in for kitchen and bathroom remodels using 14/2 Romex on 15-amp circuits
- 20-amp dedicated circuits for high-draw appliances like ranges, water heaters, and dishwashers using 12/2 Romex
- 240-volt rough-in for electric ranges, dryers, heat pumps, and EV chargers with 10/2 or 6/2 cable
- Multi-location switch rough-in for hallways, staircases, and large rooms with 3-way or 4-way wiring
- Conduit protection rough-in for exposed runs in garages, basements, and outdoor areas per NEC Article 300
- Panel upgrade rough-in when existing 100-amp service cannot handle remodel loads-upgrade to 150-amp or 200-amp
- Low-voltage rough-in for speaker wire, network cable, and audio/video feeds in kitchen islands and media rooms
Why Orlando Homeowners Choose Renovating central Florida LLC
Renovating Central Florida LLC serves homeowners across Orlando, Winter Park, Maitland, Casselberry, and Sanford with licensed, insured electrical rough-in that meets or exceeds NEC standards. We pull permits, schedule inspections, and coordinate with your general contractor so your remodel stays on timeline. Our electricians label every circuit, test every connection, and stand behind their work with a 2-year workmanship warranty. Unlike handyman electricians who guess at load calculations, we size every circuit to your specific appliances and future needs-ensuring your kitchen remodel, bathroom addition, or whole-home project is wired right the first time.
